View M62211FP_294400.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MITSUBISHI SEMICONDUCTORS
M62211P/FP
GENERAL PURPOSE MULTI FUNCTION DC-DC CONVERTER
DESCRIPTION
M62211FP is designed as a general purpose multi-function DC-DC converter. This small 10 pin package contains many functions allowing simpler peripheral circuits and compact set design. The output circuit is designed OPEN-COLLECTOR output. This makes the application for STEP-UP, STEP-DOWN and INVERTING. The input of this unit has two channels containing priority control circuit. This makes the control a simple matter when the back-light is on and during the stable state.
Notice: This is not a final specification. Some parametric limits are subject to change. PIN CONFIGURATION(TOP VIEW) Collector output 1 Emitter output 2 GND 3 Cosc 4 TIN 5 10 Vcc 9 8 7 6 IN1 IN2 FB DTC
OUTLINE 10P2N-A
FEATURE
* Wide operation power supply voltage range*******2.5~35V * Operation can be synchronized by the external sync signal * Operation can be controlled using two prioritized systems. (High input has priority) * High speed switching is possible.(500kHzmax) * Output short protection circuit and ON/OFF control are used. The dead-time control and the soft-start operation are possible * Small size 10-pin SOP package.
Collector output 1 Emitter 2 output GND 3 Cosc 4 TIN 5 NC 6 NC 7
14 Vcc 13 IN1 12 IN2 11 FB 10 DTC 9 8 NC NC
APPLICATIONS
Back-light control of personal computers and word processors General electric products
OUTLINE 14P4
NC: NO CONNECTION
BLOCK DIAGRAM
TIN 5 COSC 4 VCC
VCC
10
OSC & sync ckt
UVLO VTH : 2.3V
Collector output
OP Amp1
IN1 9
PWM Comp
1
2
Emitter output
Std. voltage 1.25V
1.25V VCC 1.86V
Short protection circuit
IN2 8
R
OP Amp2
SQ 1.15V 0.3V
7 FB
6 DTC
3 GND
(1/9)
MITSUBISHI SEMICONDUCTORS
M62211P/FP
GENERAL PURPOSE MULTI FUNCTION DC-DC CONVERTER
ABSOLUTE MAXIMUM RATINGS (Ta=25C, unless otherwise noted) Symbols Items Conditions Ratings
Vcc Vo Io Pd K theta Topr Tstg Power supply voltage Output voltage Output current Power dissipation Thermal derating ratio Operating ambient temperature Storage temperature Ta=25C Ta>25C 36 36 150 1500 (P) 450 (FP) 1.2 (P) 3.6 (FP) -20 ~ +85 -40 ~ +150
Units
V V mA mW mW/C C C
Electrical Characteristics ( Ta=25C, Vcc =12V, Cosc=390pF unless otherwise noted ) Block Symbol
Vcc All device Icc Std. VREF voltage section LINE IB AV GB Error VOM+ amp. section VOMIOM+ IOMfosc VOSCH
Items
Power supply voltage range Circuit current Standard voltage Line regulation Input bias current Open loop gain Unity gain bandwidth Output high voltage Output low voltage Output sink current Output source current Oscillation frequency
Upper limit voltage of oscillation waveform Lower limit voltage of oscillation waveform
Test condition
Limits
Min 2.5 Typ 2.4 1.19 1.25 5 80 0.6 Max 35 3.5 1.31 12 500
Units
V mA V mV nA dB MHz
No load Voltage follower Vcc=2.5 ~ 3.5V
VFB=1.86V VFB=1.86V VFB=1.86V VIN1=1V, VIN2=1V
1.7 6 -100 110 1.0 0.45 -120 30 120 2.2
2.5 400 -50
V mV mA uA kHz V V uA uA uA
VOSCL Oscil- IOSC CH Cosc charge current lator section IOSC DIS1 Cosc discharge current 1 IOSC DIS2 Cosc discharge current 2 VTINH VTINL
TIN "H" level TIN "L" level
Vcc 1.0
V V
(2/9)
MITSUBISHI SEMICONDUCTORS
M62211P/FP
GENERAL PURPOSE MULTI FUNCTION DC-DC CONVERTER
Electrical Characteristics ( Ta=25C, Vcc =12V, Cosc=390pF unless otherwise noted ) Block Symbol
VTH ON UVLO section VTH OFF VHYS VTH FB VTH DTC Short protec tion circuit VTL DTC ICH1 IDIS1 ICH2 IDIS2 Output ICL section VSAT1
Items
Start-up theshould voltage Shut-down theshould voltage Hysteresis FB threshold voltage Latch mode "H" threshold voltage Latch mode "L" threshold voltage DTC charge current when start-up DTC discharge current 1
DTC charge ccurrent when stable state
Test condition
Limits
Min 2.2 20 Typ 2.3 2.25 50 1.86 1.15 0.3 -35 45 -15 20 -1 1.6 1 80 Max 2.4
Units V V mV V V V A A A A A V
VIN1=1V, VIN2=1V, VDTC=0.7V VIN1=1V, VIN2=1V, VFB=2.11V VIN1=1V, VIN2=1V, VFB=2.11V VDTC=0.7V, VFB=2.11V VDTC=0.7V, VFB=2.11V VDTC=0.7V, VFB=0.7V VDTC=0.2V, VFB=2.11V VCE=35V, Vcc=35V Emitter follower, IE=50mA, Vc=12V
DTC discharge current 2 Collector output leak current Collector output saturation voltage
(3/9)
MITSUBISHI SEMICONDUCTORS
M62211P/FP
GENERAL PURPOSE MULTI FUNCTION DC-DC CONVERTER
1. Explanation of Back Light Control Circuit
VCC
D1
Cl
Co OSC & sync ckt
UVLO V TH :2.3V
DC/AC
FL Tube
R1 D2
Cosc IN1
OP Amp1
R3
Std. voltage 1.25V
VR1 IN2
R OP Amp2 SQ
RFL R2 R4
CDELAY
CFL
Cf2
Cf1
RDTC
CDTC Rl1 Rl2
Fig.1 An Application of the Back Light Control Circuit 1-1. Priority Control Operation As far as OPAmp1 and OPAmp2 are concerned, there is no problem when either IN1 or IN2 is used to control current, since the setting up to lower the output voltage of the DC-DC converter is prioritized. (The above figure uses IN1 to control current.) 1) When starting, the output voltage "Vo" is determined by the feedback to IN2 via R1 and R2 and the following equation : Vo=VREF * (R1 + R2)/R2 (VREF =1.25Vtyp) (Area of the Timing Chart 1) 2) Next, this output voltage "Vo" is used to discharge the FL tube by the inverter and causes the tube current to flow. The tube current is filtered and smoothed by RFL, D2, and CFL so that the DC voltage (VCFL) corresponding to the tube current is generated at CFL. The voltage of VCFL is divided by R3, VR1, and R4, and feedback to IN1, it can control tube current. (Area of the Timing Chart 2) Here, CDELAY is inserted between R3 and VR1 + R4 in order to regulate the timing to switch from the voltage control to the current control. (Area of the Timing Chart 3) When in the current control state, it is possible to adjust brightness by changing the amount of feedback of the tube current using VR1. (Area of the Timing Chart 4) If the feedback used for controlling current is lost due to irregularities in the FL tube. etc.. the control returns to the voltage control mode. (Area of the Timing Chart 5)
3)
4)
5)
(4/9)
MITSUBISHI SEMICONDUCTORS
M62211P/FP
GENERAL PURPOSE MULTI FUNCTION DC-DC CONVERTER

(V)
(mArms)
(V)
(V)
I
II IV
V
III
(5/9)
MITSUBISHI SEMICONDUCTORS
M62211P/FP
GENERAL PURPOSE MULTI FUNCTION DC-DC CONVERTER
1-2 Setting Up TIN 1) Setting Up the Level The TIN terminal is shown in Fig.a. In order for the level of TIN to satisfy the conditions shown in the table below, the external circuits shown in Fig.b or Fig.c should be used when the external voltage level of the input is high.
100K TIN 5 50K 5 5
3 GND Fig.a
Fig.b
Fig.c
Items
TIN "H" level TIN "L" level
Symbols
VTINH VTINL
min
2.2
typ
max
VCC 1.0
Unit
V V
2) Setting Up frequency The periodical change of TIN is expected to be +30% ~ -20%. The fIN is set to approximately 1.5 times fOSC fIN = 1.5 * fOSC fsoc 1 1.3s+(23 * 10 *3Cosc ) (Hz)
COSC
TIN
(6/9)
MITSUBISHI SEMICONDUCTORS
M62211P/FP
GENERAL PURPOSE MULTI FUNCTION DC-DC CONVERTER
1-3 Soft Start, DTC, and Short Protection 1) Soft Start (The peripheral circuit is shown in Fig.1) When the power is turned ON, IN1 and IN2 are at 0V level. Therefore, the FB terminal is fixed to High level. The DTC terminal goes up gradually starting from 0V due to the internal charge current and the external CDTC. When the level of DTC terminal reaches the lower limit of the triangular wave of the oscillator, PWM comparator and the output circuit go into operation causing the output voltage, "Vo" of the DC-DC converter to rise. The charge current is designed to be approximately 35A.
FB DTC 1.0V OSC 0.45V
OFF
External Tr collector
ON
Fig.2
2) DTC The dead time control is set by installing a resistor between the DTC terminal and GND. However, the DTC terminal serves as the short protection circuit also. Therefore, its set up depends on whether the short protection circuit is used and not. (When the short protection circuit is used) At this time, the charge current for DTC is approximately 10A . Therefore, RDTC should be set to 40K ~ 110K. (When the short protection circuit is not used) At this time, the charge current for DTC is approximately 45A. Therefore, RDTC is set to 12K ~ 25K.
(7/9)
MITSUBISHI SEMICONDUCTORS
M62211P/FP
GENERAL PURPOSE MULTI FUNCTION DC-DC CONVERTER 3) Short Protection Circuit The Short Protection Circuit used the timer latch system. It is determined by setting the capacity used for the soft start connected to the DTC terminal. Fig.3 shows the short protection circuit and the timing chart for various modes. When the power is turned on, the FB terminal goes high (approx. 2.4V) and the DTC terminal goes low (goes up slowly from 0V). Thus, approximately 35A current will flow when SW1:ON and SW2:OFF. The potential, namely the potential of the FB terminal is in the amplitude of the triangular wave, SW1 will be OFF and SW2 will be ON and approximately 45A will flow into the DTC terminal. This discharge current will cause the DTC terminal to drop from 1.15V. At this time, if the potential of the FB terminal goes to the control potential before the potential at the DTC terminal goes lower than 0.45V which is the lower limit value of the triangular wave and if the potential of the FB terminal is lower than the potential of the DTC terminal, then the system is activated. When the output is shorted, the system is either activated or latched depending on whether the time for the high potential of the FB terminal reaches the potential of the control state is long or short. (For detail, see [II] and [IV] of the Mode) There are two ways to go back to operation after the latch to shut off output. Either method can restart with soft start. 1. Turning ON the Vcc. 2. Make the FB terminal to go to the low potential of 1.25V or less. Then, it is cancel led. [Mode Explained] [ I ] Mode ************ Activation This is used when the FB terminal goes down to the control state potential when the DTC terminal is in up slope. In order for the activation to occur when the DTC terminal is in down slope, the FB terminal potential must go below the DTC terminal before the DTC terminal goes to 0.45V. [ II ] Mode ************ Output short --> Activation The system is activated if the FB terminal potential goes below the DTC terminal potential before the DTC terminal goes to 0.45V. If there is not enough time, the output is turned OFF (Latched) [ III ] Mode *********** ON/OFF Control --> Activation This mode turns off the output by forcing the DTC terminal to go down. (The system) returns as in the case of the activation. [ IV ] Mode *********** Output Short (Latch) The output is turned OFF when the FB terminal potential did not go down to the control state before the DTC terminal went down to 0.45V.
(8/9)
MITSUBISHI SEMICONDUCTORS
M62211P/FP
GENERAL PURPOSE MULTI FUNCTION DC-DC CONVERTER Comp1 FB 1.86V (Initial RESET) R Q
1.25V I1 10 SW1 DTC I3 55
Vcc I2 25
S
CDTC
RDTC 90K (900mV) SW2
Comp2 1.15V 0.3V
* SW1 and SW2 are turned ON by "H" signal.
FB
2.0
1.15 1.0
DTC
DTC set up value (Tentative)
OSC 0.45 0.20 0 I1 I2 I3 ON ON OFF ON OFF ON
45
ON OFF OFF
Charge 10
ON OFF ON
Discharge
ON OFF OFF
Charge 10
ON ON OFF
35
ON ON OFF
35
ON OFF ON
45
ON OFF OFF
Charge 10
ON OFF ON
ON ON ON
Charge Discharge
Charge Charge Discharge
35
45
Discharge Discharge 45 20
Activate [I]
Output short
ON/OFF control --> Activate
Output short (Latch) [ IV ]
[ II ]
[ III ]
Fig.3 Short Protection Circuit and the Timing Chart of the Modes
(9/9)

▲Up To Search▲

Price & Availability of M62211FP

	To Download M62211FP Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .